300 hp N/A carb 2.8 V6 engine

[robertisaar]

I'm not sure how you would use a mic to check bearing clearance to begin with.

Plastigauge is for lawn mower engines! Micrometers should be used on high performance engines.

I know a few professional engine builders who build high performance engines and use Plastigauge. It's really the only way to know actual clearance, when things are torqued down.

[23TrackroadsterV6]

Plastigauge is for lawn mower engines! Micrometers should be used on high performance engines.

[geoffinbc]

Its tight but do you have a mic and telescoping gauge you can measure with? Plastigauge is a great double checking tool when doing a re and re but not good enough for a race motor.

[veekuusi]

That's .0015"... That's good for a race engine, but I wouldn't want it any tighter than that. Have you had the mains bored or honed? If you torque all the main caps down, how much torque does it take to rotate the crankshaft?

Everything has been done by the book.
I mean by the Benīs book.

I do not know about the torque but the crank rotates quite easily.




You better check the video:

https://www.youtube.com/watch?v=fItQSeMX1GA&feature=youtu.be

[Will'sFiero]

That's .0015"... That's good for a race engine, but I wouldn't want it any tighter than that. Have you had the mains bored or honed? If you torque all the main caps down, how much torque does it take to rotate the crankshaft?

[veekuusi]

Main bearing clearance .040 mm
Too tight or not

[veekuusi]

It`s time to get things started.

[geoffinbc]

ATI does make good dampers. Elastomer is the way to go and it seems by the description they have 2 ring diameters supported by an elastomer so it will not be tuned to just one frequency, which is good. That being said the short crank of the V6 is not prone to huge harmonic problems (like a longer V8, or worse an I6, crank) but any engine running on the street or sustained RPM racing really needs to have a damper. Drag racers don't need one because the RPM's are always changing the entire run so the variable frequency never lets resonance set up. Since your racing the SFI rating of the ATI damper may be a requirement too. A stock one is no good for some sanctioning bodies. The cast outer ring may explode without warning at 7000RPM.

[veekuusi]

I sent Crower a sample, one stock internally balanced crank from 2.8 engine.
The idea was to make a internally balanced billet crank.
And thats what Crower did.
They seem to add two pieces of mallory metal to the crank to make it perfectly balanced.

I asked the Crower people , what kind of damper should I use with the new billet crank.
Or should I use no damper at all.
There was a ATI Super Damper in the destroyed engine.
Crower recommended ATI-dampers.
"They are good, I would use one" was the exact answer from the "expert".

http://www.summitracing.com/int/parts/ati-917190/overview/

[geoffinbc]

Looks to be internal balance. It has dual weights on the rear. As far as the 60 degree V6 is concerned the harmonic damper on the front has nothing to do with the balance of the crank.

[unchained01]

I hope that missile works very well and your intake makes the difference Can I ask is this crank an internally balanced or are you going to use a damper ?

[geoffinbc]

Wicked. I can't remember but did you send them an original cast crank to copy?

[3400-95-Modified]

Take a picture, it will last longer....... Well actually I hope the both last as long. LOL

[1988GTU]

I'd almost be tempted to put that piece in a glass cabinet for display. But with me, the power hungry appetite trumps beauty.