Exhaust Collector Discussion

[Superdave]

I made some true merge 3:1's for my current longtubes, had to use paper templates and an air nibbler to cut the tubing right. then a die grinder with a carbide cutter to clean up the seams on the inside. A Plasma cutter would be VERY nice for this...

It was a royal pain in the ass but i guarantee they are better than the cheepie 3:1's i was using before.

[geldartb]

A few years ago i was testing some exhaust stuff for the 60v6 and built a pulse rig using 3 120VAC air solenoids hooked up to the air compressor. I was using a variable speed DC motor with a cam on the end to actuate some microswitches to pulse the solenoids and push air through the primaries. It actually worked pretty well.

too bad i dismantled it and turned it into a air gun... but it'll shoot a 3" screw through 2 layers of drywall @ 120 PSI

haha almost a better use for it. more fun though

[SappySE107]

I made this its own discussion, since its not about porting Other thread is dead.

[HOYS]

Oh yeah, I used a dremel to cut the steel pipe for my turbo manifold, then used a sand roll to make the ID just right. Merging 2 pipes smoothly is much easier then 3. It took some time but it was worth it.

[ATTACH=CONFIG]6045[/ATTACH][ATTACH=CONFIG]6046[/ATTACH]
The turbo manifold wasn't fully welded in these pics, but it shows how anal I am about the boundary where the two meet, I spent a while grinding smooth and polished it.

I determined few things before I started to build this engine up, optimize intake and exhaust as best as possible was one of them. The exhaust post-turbo is done and the entire length has zero interference along the way (within reason). The exhaust is wide open and the only resistance is the dual flowmaster 40's.

The y-pipe that splits the exhaust into dual (fake dual exhaust, lol) was also cut just right and equally divides the exhaust flow.

What happened to that crossover!

Is there proper clearance for the wastegate and the turbo?

[TGP37]

I don't know if that is what will happen though unless you have equal length primaries, and even then you want the smoothest transition possible for each pulse to retain its strength. The speed of the exhaust vs the length of the primaries will determine when if ever that vortex could be created.

Yeah, getting equal length primaries is very important considering the designs ambitions. If the bends are mandrel and the seams are butt welded with the edges matching right, I bet most of the charge remains intact and relatively geometric in shape instead of scattered.

If anything I know they will work better then regular 3 or 4 primaries shoved in a larger diameter pipe. I see many collectors that merge but only after the 4 are laid out. The pulses ability to make a negative wave up the other primaries will degrade upon resistance. A knife edge merging with a nice curve should provide a fantastic reflection.

I am modeling a cylinder head and going to make boundary boxes to indicate the room I have to design in. Then I can build a studio max header, and each piece can be attached but rotate freely. So then I can create the longest primary then bend it to fit the other two, virtually that is.


I like this design idea better since it involves the pinching of the pipe diameter after the primaries. I notice other headers utilize the same principles. So this idea has a plus.


Then all I need to do is build the primaries virtually. Best thing is I worked with particle systems in Studio Max before, other art stuff. Many people have successfully used the particle system to mimic smoke, fire, air flow, etc. So I built the collectors with that in mind. the geometry can support the particle system and reflect. It would require a lot of data collecting, like surface tension, surface roughness, hardness, etc. Plus the particle flow would need to wane in and out like a real engine would. As the valves don't open instantly but there is a higher flow in the beginning. I might be taking this too far but it is fun.

I probably just build the collectors for now. Worry about the primaries when I get to that point in time.

[TGP37]

Hoys, there is the end result. It all fits great, no leaks and its VERY strong. But has 3 flex joints to allow variation while operating. No cracks here....lol

I know it looks sloppy but that is the best I can get with this flux core welder. I double up the weld seams, the first round was the typical hot weld, merges great with the steel pipe. But the last round is a reinforcement.

I care more about function over appearance. It actually holds the exhaust wrap better.

[SappySE107]

Nope, it won't stay geometric even if you used a straight piece of tubing. Since it isn't steady flow, it is going to roll and tumble its way around inside the tube. It was probably on speedtalk that I saw the pictures of how the flow worked it way through the tubes, but I don't recall how they even had the pics. Ah, the novelty of forgetting details What I gained the most was to forget about making any real sense of it without testing. The varying lift of the exhaust and the cam timing will be a part of this (and imagine variable cam timing, woohoo!).

[pocket-rocket]

I know it looks sloppy but that is the best I can get with this flux core welder.

Spatter spray and preheating the tubing with either propane or MAPP could have helped. Better late than never, and yes, function over appearance. I think that's the definition of fugly. Fast + UGLY= FUGLY

[slw240sx]

I know you guys will probably not take a word i say as legitimate as the bias here against people from our side of the coin seems rather high. I can not speak on daves attitude as he says and does what he wants most of the time. Even to the point where i have fired him in the past because of negative behavior and the outlook it had upon my shop. I have rehired him before and he works for me part time when i need help around the shop. He has a wealth of knowledge, unfortunately his immature attitude often discredits his knowledge.

This is about giving you guys good information though. I am not here to bash on anyone, just to offer up my advice and constructive criticism. I come from a turbo building background, i have owned a shop for the past 5 years and we have built more cars then i care to remember almost every one being turbo. In all my years what i have learned most is that people often over think 90% of what they are trying to do. i have sat and read this thread and the porting thread and i have come to the conclusion that you are all just over complicating this issue when it comes to building a turbo kit. You do not need these fancy collectors you are trying to build. a simple press / stamped collector will work just fine for any HP level you intend to hit. I have used pressed style collectors on 700-800hp cars they were 4-1 collectors on v8 motors, but they work well. the 3-1 collectors will easily get you into 500hp range no problem they are not going to hold you back from making the power. the twist merge collector is just to time consuming to even worry about. yah its cool to cad things out and try them, but when it comes down to it. The time invested vs gain over normal collectors will be not worth it. i am not against building a merge collector over using pressed collectors. I am against it on a production kit that uses 16-14 gauge mild pipe due to costs. If i were building this out of schedule 10 304 SS weld L's i would spend the time to build a proper merge collector.

I have spent countless nights looking over collector designs, collector fixtures, and welding techniques for them. I have found one really great wealth of information that i will pass on to you guys. Keep an open mind. the link i am giving is for a Honda forum. This honda forum though is more then just about hondas, they have a section dedicated to fabrication. The leading people in the sport compact and fabrication industry regular this forum and the amount of information and displays of work is amazing. I go here often for inspiration and to keep up on what is happening and to soak up new things. here is actually a really good "how to" guide on building merge collectors. These collectors actually use the stainless steel schedule 10 material i was speaking on earlier, but the techniques can be used on thinner materials. http://honda-tech.com/showthread.php?t=2787713
the link to the welding and fabrication subforums http://honda-tech.com/forumdisplay.php?f=53

You said you have 3 flex joints in the system? that alone will cause a nasty flow disruption that even the perfect merge collector would have trouble correcting. I personally try to avoid flex joints anywhere pre turbo as they do not hold up to the extreme heat very well, nor do they flow very good with most having a internal bellows instead of a smooth surface. Also the heat wrap while helping to keep the exhaust gas velocity up will actually do more damage to the pipes faster causing severe metal fatigue quickly leading to failure of the material. I had a customer that we built a set of turbo headers for a ford 302 and they were ceramic coated, but he heat wrapped them. the wrap held in a good amount of heat which over heated the coating resulting in a failure of the coating, and then led to a failure of the material around the collectors from where the heat concentrated. The collectors actually ruptured and came apart. This kit was only a few months old and it looked like an old burn barrel. the coaters refused to warranty the coating and i had to refuse to warranty the headers because he was warned ahead of time. I try to avoid the stuff at all cost when its near the heads. I can see doing the parts of the exhaust as it passes under the car because the heat there is less extreme, but it will help keep heat out of the cabin.

I know you are doing what you can with a flux core, and i admire your DIY attitude! if i did not have the same DIY ethic i wouldnt have ended up with a turbo shop! I do though offer a suggestion on building the stuff. I see that you have a higher understanding of all this, but lack the finer skills to execute them. dont take that the wrong way its not a dig at you, it takes years to learn how to do this stuff and make it pretty and reliable. I have a good number of customers in a similar situation, they have the basic understanding of how to fab, they do not want to pay a shop to build their cars, but they want a good part. So what i offer to them is for them to build what they want. they are always welcome in the shop to ask questions, get pointers, and to bounce ideas off me. Most take me up on that and what we work out is that they will get together what they are building and tack weld or mark out parts for welding then bring it all over to me for final welding that way their parts come out looking for the most part professional. you cant always get the finished look of a pro due to their beginner skill, but it looks way better then what it would have had they done it all themselves. They get their parts on the cheap and i get to help them out in turn they keep the word about us moving around. i would suggest hitting up a local fab guy whether it be a speed shop like us or even a local weld shop with that 50-60 year old redneck as long as they have a tig welder they can probably get you going! keep up the work and keep posting pictures!

Jon @ ForcedFab

[TGP37]

...

Jon @ ForcedFab

omg, you posted a book, lol.

There is nothing wrong with exploring an idea. The twisting part is more a curious intention, the real part of the collector is merging smoothly. I am a beginner with turbo building BUT, I can not let go of a common knowledge of physics.....a better merge will make better flow.

2 flex joints pre-turbo, and they are just before the merging of the cross-over. the other is before the test cat.

It seems you think I am building a high boost car. I agree with most of what you posted, but is over kill for a 5-8 psi turbo. I dont even consider hitting 15 psi, though it was built in mind to hit that high.

I just can not tack 3 or 4 pieces of pipe together and call it half a collector. Sure, its fine to use and works but, I am a diy builder (not just turbos) and if I can do better, I will. And even though the welds are really ugly, they are strong as ever. I dont weld for looks, I weld for a molten bond between steel and welding material. I tack weld but each weld is literally melted into the pipe, not just steel glued. It is messy but I could weld two 4' pipes together and stand on the seam w/ ends on a brick or something.

Ahh its okay dude, I will be fine. What is over thought for others is daily day dreaming for me. Thanks for the links

Nope, it won't stay geometric even if you used a straight piece of tubing. Since it isn't steady flow, it is going to roll and tumble its way around inside the tube. It was probably on speedtalk that I saw the pictures of how the flow worked it way through the tubes, but I don't recall how they even had the pics. Ah, the novelty of forgetting details What I gained the most was to forget about making any real sense of it without testing. The varying lift of the exhaust and the cam timing will be a part of this (and imagine variable cam timing, woohoo!).

I understand now, I was caught in a visual error. More like water rushing down a curving water slide?

I know one thing, that flow is anything but linear after squeezing threw the valves...lol

Spatter spray and preheating the tubing with either propane or MAPP could have helped. Better late than never, and yes, function over appearance. I think that's the definition of fugly. Fast + UGLY= FUGLY

Fugly, haha. We used that in High School for the "FAT" and Ugly. A friend may have nailed an ugly chick, we just shake our heads and tease them. But a real friend won't let friends tag a fugly chick...no matter how wasted.

I considered making copper shield with magnets attached, the right diameter for the pipe being welded. Just set them in place and go. But then, spatter never really bothered me much and has been great holding the wrap in place. If I was welding a piece that is in view, I would then take steps to reduce spatter.

[TGP37]

I made some true merge 3:1's for my current longtubes, had to use paper templates and an air nibbler to cut the tubing right. then a die grinder with a carbide cutter to clean up the seams on the inside. A Plasma cutter would be VERY nice for this...

It was a royal pain in the ass but i guarantee they are better than the cheepie 3:1's i was using before.

What kind of gains did you see? Or is that an unknown?

I do believe they are better, just how much better is the question I think about. I have a paper mache' like replica of the mandrel bend. Made them w/ glue soaked paper strips and let dry. They turned out really well. But I plan to mark a grid over the temps to match the wireframe on the virtual design. Transposing the curve lines wont be hard, just time consuming. But I'll have a set of templates to use over and over again. So the next 5 cut pieces will be easy.......hopefully.

[pocket-rocket]

......


Jon @ ForcedFab

Not to thread jack, but...

You seem to be an extremely down to earth guy, I respect that. Had Dave come in here with the same attitude you presented yourself with I'm sure many more would have taken him more seriously.

Thanks for the links, I'm going to give them a look over as I'm always looking for information to make my knowledge more broad in the world of modifying cars. I know most guys here are open minded enough to read over Honda forums, as most here aren't that closed minded like some of the back woods "nothing can beat my V8" kind of guys.

[bszopi]

Jon,

I would also like to welcome you, and thank you for joining the forum. I follow your posts over on GAGT.com, but unfortunately can no longer post over there. But anyways, I fully agree with everything you have said, and just to note, Ben and I often link people to a Honda (primarily) resource for the excellent information on general engine dynamics: http://theoldone.com/ Being in the world you are in, I would hope you have heard of Endyn and Larry Widmer.

[TGP37]

hey Jon, I now realize your advise has more weight then previously thought. Unfortunately my first impression of you was stained by the "Dave" drama. But I know better then to judge another by such little understanding who they are.

In light of that, I'm sorry if I came of with the "Better then thou" attitude.

Now, this turbo project is more of a personal mission then just making a turbo. I aim to perfect a lot more then most would consider, even though I am a novice. Like Sappy said recently, some things are just dreams, but other things are potential points to squeeze a little more efficiency, performance, etc. Besides the time spent, I do firmly believe refining a header collector (with respects to the entire build) will provide less turbulence in the center where all 3 primaries meet up.

I have not made a final choice of material to use or the gauge. But you mentioned Sch10 Stainless Steel?

This design I am working on is the 3rd round of manifold design for the turbo. The 1st was just the cross over cut open with 10 gauge steel plates welded to a box, to the turbo flange. It worked but was obviously restrictive as the two sides impacted each other head on.

The second design, which is the current one, has A LOT of thought to geometry and flow. But still, it is based off the stock log manifolds. And I feel I can do a little better. So for now the current one stays on while I take the time to design a superior cross-over turbo manifold.

CAD designs are great for initial layouts. Once I set the boundaries where I can place the primaries/collector, I can design it and find a way to make all 3 primaries equal length with as little as bends as possible.

Any advise you wish to provide is 100% welcomed. Sorry about the book comment, like I said earlier, I associated you with Dave. But I take that back now.

[SappySE107]

I know you guys will probably not take a word i say as legitimate as the bias here against people from our side of the coin seems rather high.

bias through experience. Ill take it.