Tweet
Hey i have 01 3100 topend, can someone tell me the stud is 47 lbs? and the roller rocker is 18 lb? It is turbo so i want to make sure.... any help apreciated, btw i dont have a 3100 manual...
-
-
dont remember when they changed the stud size but this is from my 99
Rocker arm bolt 14 N.m (124 lb. in.) plus 30°sigpic
99 Grand Am GT
3400/3500 -Solid trans mount--TCE 65mm T-body---85mm LS2 maf---1 1/4' TCE intake spacers with 3400 upper--SLP Catback with flowmaster 80--TOG headers
Modded 3400 lifters with LT1 springs---Comp Cams 26986 Springs
1357 cam 227 233 .050 dur 515 515 lift 112 lsa
15.232@88.85mph on stock 3400---New time to come
-
sounds right^^^94 BerrettaZ26 3400,5 spd, aluminum flywheel, stg3+ spec clutch, poly mounts everywhere, strut and strut to rad braces, s&s headers, euro mirrors, and taillights, E36 headlights, blk widow spoiler, GTU rimz, intrax, KYB, OBD2 swap rear disk swap with ss lines and ss clutch line, addco rear bar
07 Chrysler 300 Base, with C frt bumper blk halo headlights and foglights. Coming soon tinted taillights and 22". The Family ride
Comment
-
i got that from my alldata online so it better be right.sigpic
99 Grand Am GT
3400/3500 -Solid trans mount--TCE 65mm T-body---85mm LS2 maf---1 1/4' TCE intake spacers with 3400 upper--SLP Catback with flowmaster 80--TOG headers
Modded 3400 lifters with LT1 springs---Comp Cams 26986 Springs
1357 cam 227 233 .050 dur 515 515 lift 112 lsa
15.232@88.85mph on stock 3400---New time to come
Comment
-
I torqued my 97 lumina's to 25 ft/lbs. then drove it for another two years w/o problems--even after I found out that at 35 ft/lbs the threads in the heads are at the max!. yep! heli-coiled it!
i didn't have a way to measure degrees haha oh well!
Andy
sigpic
fastest 1/8: 10.19@ 67.17
fastest 1/4: 16.16@ 82.70
62mm TB, 1.6 roller tip rockers, Ostrich 2.0, UD pulley, TB heater bypass, K&N, 180* stat, No cat, 99Grand AM dual cooling fans. 4T65E swap FDR 3.69, EP LSD, F.A.S.T. transmission controller, TransGo shift kit.
Comment
-
1 flat = 60 degrees.
Note that Geldartb said 124 INCH-pounds plus 30 degrees. Not Foot-pounds. There's always some rocket-scientist who confuses these two... resulting in broken parts.Comment
-
Who ever tightens their rockers to 124 ft pounds shouldnt be working on a motor....Comment
-
damn that reminds me i need an inch pounds torque wrench and a torque wrench that goes higher than 75 ft lbs. at the time that was higher than anything i was doing.sigpic
99 Grand Am GT
3400/3500 -Solid trans mount--TCE 65mm T-body---85mm LS2 maf---1 1/4' TCE intake spacers with 3400 upper--SLP Catback with flowmaster 80--TOG headers
Modded 3400 lifters with LT1 springs---Comp Cams 26986 Springs
1357 cam 227 233 .050 dur 515 515 lift 112 lsa
15.232@88.85mph on stock 3400---New time to come
Comment
-
-
i you can't torque the rockers to 124 ft/lbs. the threads will strip out waaayy before that. damn aluminum.Andy
sigpic
fastest 1/8: 10.19@ 67.17
fastest 1/4: 16.16@ 82.70
62mm TB, 1.6 roller tip rockers, Ostrich 2.0, UD pulley, TB heater bypass, K&N, 180* stat, No cat, 99Grand AM dual cooling fans. 4T65E swap FDR 3.69, EP LSD, F.A.S.T. transmission controller, TransGo shift kit.Comment
-
Hrmmm I always just made them tight... without a torque wrench... never had a problem with mine.
Got Lope?
3500 Build, Comp XFI Cam 218/230 .050 dur .570/.568 lift 113LSA
Fully Balanced, Ported, 3 Angle Valve Job, 65mm TCE TB, S&S Headers.
Stage-1 Raybestos/Alto 4t60e-HD, EP LSD, 3.69FDR
12.61@105 Epping NH Oct 2015 Nitrous 100shot (melted plugs) 13.58@98.8 N/A 3200LBSComment
-
Impact gun FTW!
I forget what I put mine at but it's what chiltons said and it's just torq and this it, no extra turning. Done it 3 times and no problems.sigpic
New 2010 project (click image)
1994 3100 BERETTA. 200,000+ miles
16.0 1/4 mile when stock. Now ???
Original L82 Longblock with LA1, LX9, LX5 parts
Manifold-back 2.5" SS Mandrel Exhaust. Hardware is SS too.
Comment
Comment