Quarter Mile Times

[1QUICKHATCH]

I got two slips of when I ran the 15.54 but I haven't got them scaned yet

[brian89gp]

As for me, with my 62mm throttle body, I do not have to worry about fuel economy. Thanks to the wonderful Ben, and his custom chip with LEAN CRUISE, I get about 45 MPG HIGHWAY. But if I am not on teh highway, I usually average about 8 MPG (curse my lead foot).

Holy hell, thats up in the range of those stupid looking hybrid cars. I am jealous, very jealous.

[StudlyCamaro]

i ran a 15.935 with a 2.18 60'

that is a fuckign fast 60' for such a slow 1/4mi
(no offense, but comparitably)

i was on slicks. i have the slip if you would like to see it... i think it might be on the net too.. i'll post a link to it if i find it

[SappySE107]

Im not going to tolerate hatred and ignorance. Leave aaron alone, this is a thread about what you run. Are you that much of an asshole to tell him he can't post his time in here? Maybe you are pissy cause he runs a 14.7 and doesn't own a pushrod. Whatever your problem is, it is YOUR problem.

.2 difference from elevation? Thanks for the laugh, you have no clue.

[Anonymous]

I ran a 15.3 @ 89.1 in my DOHC... bow down bishes!

I STILL want to see jweir22's timeslip. I CANNOT believe that a 3100 in a W-Body would run a 15.65 @ 90.8!!

[imported_RebelGT]

getting back on topic.....

16.0 1/4, stock motor 3.1 mfi atx, on all seasons.

my best 60' foot was a 2.2 with shorter slicks.

[bszopi]

To just reiterate what Ben said, those of you who decided to act stupid and immature, your posts have been deleted. If you feel the need to bash on someone like that, take it to another forum.

[Anonymous]

Im jealous. You guys are pulling these 2.2 and 2.1 second 60's. damn, MY BEST run of the night only yielded a 2.3 yet my ET was quite lower than yours.



*Dreams of having torque and slicks*

[StudlyCamaro]

*Dreams of having torque and slicks*

what size tires do you run?, i got 4 slicks mounted on a set of Z28 rims for 100$, and the slicks still had some life left in em

[imported_RebelGT]

the slicks i used were 1.5 inches shorter than stock, so they increased the bottom end quite a bit, but of course my times were really poor.

once i get to the track again i should be able to pull some runs pretty deep into the 15's which will be pretty cool i think, and after i get the turbo motor built, who knows

[StudlyCamaro]

1.5 inches.. damn... i thought mine were shorter than stock.. i have a 50 sidewall stock , and my slicks were 45 , lol

[Anonymous]

*Dreams of having torque and slicks*

what size tires do you run?, i got 4 slicks mounted on a set of Z28 rims for 100$, and the slicks still had some life left in em

At the time I used 245 Crappy tires. Now I use 235 Yokohamas. They grip quite a bit better, even if they are smaller.

[StudlyCamaro]

hope on an f-body board, you can find used et streets, hoosier QTP's, m/t DR's , and nitto 550's for cheap , and they hook great, i usually cut a 2.3 or so on street tires cause i cant keep em from spinning off the line, but with my victoracers i dead hook most of the time (they are very used, if they were new i be they would be a lot nicer

[Anonymous]

Thanks, I will once I get my car closer to finished, ie headers and my other things done.

[Canada]

5 speed DOHCs are a bitch to launch.....power comes on HARD and QUICK.....ever take a look at the dyno charts? Its either bog or wheelspin....sometimes both. BUT when you are able to get it right......you'll run not slow.