How do you remove the fork on a 1990 Beretta getrag 282 external slave. I need to replace it and I don't understand how to remove it
Announcement
Collapse
No announcement yet.
Fork removal? Help
Collapse
X
-
Tags: None
-
This one?
I'd say loosen the arm at the top so it slides around, then rotate the arm away from the trans so the fingers are not on either side of the output shaft and then see if it will slide up to release the bottom, then angle the whole rod away from the trans and slide it back down. This is only a guess from looking at this photo though, I've never removed one before.Last edited by 3400-95-Modified; 03-11-2013, 12:21 PM.
Got Lope?
3500 Build, Comp XFI Cam 218/230 .050 dur .570/.568 lift 113LSA
Fully Balanced, Ported, 3 Angle Valve Job, 65mm TCE TB, S&S Headers.
Stage-1 Raybestos/Alto 4t60e-HD, EP LSD, 3.69FDR
12.61@105 Epping NH Oct 2015 Nitrous 100shot (melted plugs) 13.58@98.8 N/A 3200LBS
-
I asked a guy on Bnet who I know had to replace his... the picture above is actually the trans he did it on. I'll let you know what I get for a reply.
Got Lope?
3500 Build, Comp XFI Cam 218/230 .050 dur .570/.568 lift 113LSA
Fully Balanced, Ported, 3 Angle Valve Job, 65mm TCE TB, S&S Headers.
Stage-1 Raybestos/Alto 4t60e-HD, EP LSD, 3.69FDR
12.61@105 Epping NH Oct 2015 Nitrous 100shot (melted plugs) 13.58@98.8 N/A 3200LBS
Comment
-
Jon's pretty much got it. Loosen the slave cup and slide it toward the input shaft. Pop that end cover off with a screwdriver and start sliding the fork through the hole until it comes out of the bushing. Then just angle it forward and pull it back through the hole you just slid it in to.
91 SS . 3400/5spd - S&S, TCE, EP, FFP, SPEC, DSS, K&N . GEARHEAD dezign
Comment
-
It's just pressed in. The service manual specifies a screwdriver but I can't remember what I used. This was quite a while ago now.
91 SS . 3400/5spd - S&S, TCE, EP, FFP, SPEC, DSS, K&N . GEARHEAD dezign
Comment
-
which bearing?
Got Lope?
3500 Build, Comp XFI Cam 218/230 .050 dur .570/.568 lift 113LSA
Fully Balanced, Ported, 3 Angle Valve Job, 65mm TCE TB, S&S Headers.
Stage-1 Raybestos/Alto 4t60e-HD, EP LSD, 3.69FDR
12.61@105 Epping NH Oct 2015 Nitrous 100shot (melted plugs) 13.58@98.8 N/A 3200LBS
Comment
-
Got Lope?
3500 Build, Comp XFI Cam 218/230 .050 dur .570/.568 lift 113LSA
Fully Balanced, Ported, 3 Angle Valve Job, 65mm TCE TB, S&S Headers.
Stage-1 Raybestos/Alto 4t60e-HD, EP LSD, 3.69FDR
12.61@105 Epping NH Oct 2015 Nitrous 100shot (melted plugs) 13.58@98.8 N/A 3200LBS
Comment
-
That's just not going to happen unless you get shit lucky and find something similar. Parts for those transmissions don't exist on any local parts shelves.
Got Lope?
3500 Build, Comp XFI Cam 218/230 .050 dur .570/.568 lift 113LSA
Fully Balanced, Ported, 3 Angle Valve Job, 65mm TCE TB, S&S Headers.
Stage-1 Raybestos/Alto 4t60e-HD, EP LSD, 3.69FDR
12.61@105 Epping NH Oct 2015 Nitrous 100shot (melted plugs) 13.58@98.8 N/A 3200LBS
Comment
Comment