95 GTP 5 Spd Swap and OBD 2 w/ 96/97 Engine..

[94GPGTP]

heres the C200. may or may not need to play with it. posting them in case. removed the sections that were not needed.

I compared the two and looks like nothng needs to be changed. That's good.

A couple more things. Is there a pinout for the diagonisc port for the 96?

Also could you geta pinout for the interior side of the C100 on both.

Another thing would you happen to know where the DIC gets it's information. So far I haven't seen anything to to the DIC.

[pocket-rocket]

Another thing would you happen to know where the DIC gets it's information. So far I haven't seen anything to to the DIC.

In OBD1 I was always under the impression it gets its data stream from the diagnostic port, but with OBD2, I'm not sure...

[robertisaar]

the C100 pinouts include interior and exterior. thats what the (M(ale)) and (F(emale)) were for.

getting ALDL and DIC now...

Done.

[94GPGTP]

the C100 pinouts include interior and exterior. thats what the (M(ale)) and (F(emale)) were for.

Ahh i didnt see that..

Thanks for the info so far man you have been alot of help..!!!

If i need anything else ill let ya know..

[robertisaar]

If i need anything else ill let ya know..

works for me...

[94GPGTP]

Well the 96 lumina is finished.. i put that back on the ground rolled it out and brought the Z34 in.. Suprising the Z34 started and ran so i drove it like a 1/4 mile before i put it in the garage for teardown.. I got the hood off and the radiator out and starting to take the wiring off without cutting it since it is sold.. I also got the CV's out and the tie rods and ball joints broke loose and off.. Exhaust downpipe off and all nuts holding engine mounts to subframe off.. Its ready to come out after i get the steering shaft off and the rest of the wiring.. Its going pretty fast.. a couple pics so far.. Right now im on break since im at a halt because the C100 tork bolt is stripped and i dont know how to get it off without cutting wires.. so the buyer of the harness was contacted and waiting for a reply from him.. here is a few pics.. more later after the day of working is over..







C100 stripped bolt

[pocket-rocket]

I envy your work area...

[1988GTU]

Gawd that mo-taR is gigantic. Looks like an anchor for the titanic!

[pocket-rocket]

Gawd that mo-taR is gigantic. Looks like an anchor for the titanic!

No, that would be the L67.

[robertisaar]

No, that would be the L67.

"repurposed" motors.... easier than recycling!

[pocket-rocket]

"repurposed" motors.... easier than recycling!

They might fit in a 1st gen, but not so well in a recycling bin

[1988GTU]

They might fit in a 1st gen, but not so well in a recycling bin

lol

[94GPGTP]

So now the Z is finally done being stripped for all the 5 spd components.. Today i got the firewall plate out along with the shifter and cables.. Pretty much it is all ready to be torn down and customized to fit in the 95.. I have pictures of everything.. I had my neighbor make some brass bushings for the shifter cable ends and you will see them.. :high5: Also i took a few pics of all the 284 crap i have and ill tell ya its alot.. Just about enough for 2 complete swaps..

[94GPGTP]

Bought the spec stage 2 clutch last thursday.. I am in the process of tearing down the 96 engine to put new gaskets on the lower end since it was lesking oil like crazy.. I am not pulling the oil pump dummy drive since it is not leaking but i do want to clean it like crazy and silicone the thing up a bit to keep it from leaking.. I am doing the timing chain cover gasket along with intermediate shaft seal front and rear seals and oil pan.. LIM and UIM.. and T-belt.. i need to block off the AIR and EGR ports/port in the manifolds yet on the exhaust.. So i am awaiting the clutch to come in.. then get the flywheel resurfaced, and get my motor back together.. I will then mate the engine and trans together and get it all one piece and get my car preped to do the swap.. its taking a little longer than expected to do this swap but i have not touched my car and will not until i know im ready to dig into it.. I have bought another Grand Prix and in the process of trying to get another on this weekend..