Tons of engine stuff

[Fearfactory17]

i have atleast 3 engines worth of parts. i have two 2.8 v6s, totally taken apart, one was an 89 TPI and the other was an 86 TBI, i also have tons of stuff for a 3.1 all of the parts are in great shape and have at the most 30,000miles on them.

i also have RWD driveshafts and an AC compressor. and a power steering pump off a 93 lumina. so please, if you need anything at all for these engines chances are i have them. the aluminum heads of the 3.1 are in AMAZING condition.

i just want to get rid of this stuff. offer me a price and im sure ill take it, just message me with what you want and ill give you a price.

i also have a 700r4 out of an 89 firebird. the only thing it need is a new shift linkage. its like a $20 dollar part. the fluid was not burnt up when i drained it and shifts fine.

im located in ohio.

any questions, message me.

[Guest]

I take it the 2.8s were genI (iron head)?

[ForcedFirebird]

So you have a good bare block?

[Fearfactory17]

yes i do, its been sitting for a while in my garage so it propably needs cleaned and honed real well. but it ran before i took it apart.

[Guest]

*tap tap* Is this thing on?

[ForcedFirebird]

yes i do, its been sitting for a while in my garage so it propably needs cleaned and honed real well. but it ran before i took it apart.

RWD? What's the zip, so I can estimate shipping? How much do you want?

*tap tap* Is this thing on?

You have a cloaking device too?

[Fearfactory17]

sorry raven yes the heads are cast iron, they are bare(no valves or springs) andthe aluminum ones are complete.

forced firebird, ill have to find out about shipping, the zip is 44281. i have a 89 block out of a firebird, cylinders are fine, no cracks or scratches and the taper is within specs. then i have a 3.1 block out of a 91 lumina which is in amazing shape, im not even sure if it was ever ran. and im pretty sure both blocks are the same.

i have all the accessories for these engines if you need that too.

[ForcedFirebird]

sorry raven yes the heads are cast iron, they are bare(no valves or springs) andthe aluminum ones are complete.

forced firebird, ill have to find out about shipping, the zip is 44281. i have a 89 block out of a firebird, cylinders are fine, no cracks or scratches and the taper is within specs. then i have a 3.1 block out of a 91 lumina which is in amazing shape, im not even sure if it was ever ran. and im pretty sure both blocks are the same.

i have all the accessories for these engines if you need that too.

The motor mounts should be different between the Lumina/Firebird block. When you say block, I don't need the pistons etc. Actually, I take that back, I could use that 3.1 crank from the Lumina and the block from the Firebird. I have a set of 170 casting aluminum heads and .030 over pistons to go with it. All the accesories will be comming off the motor that is in the car.

[ForcedFirebird]

How much for the block and crank, and do you have paypal?

[Fearfactory17]

how does $200 for both sound? the 3.1 crank is in real good shape, i could measure it with a micrometer for you if you want. just so you know it is haha

[ForcedFirebird]

Ouch,$200+ $120 for shipping with UPS. I can get a complete motor for $350 local, but I have to pull it.

[Fearfactory17]

well what seems fair, i just want this gone.

[Guest]

Do you have the dizzys from the iron head engines? If so what would you want for both?

[Fearfactory17]

i only have one $35 shipped