Tweet
ive got a 3500 short block for sale, im using the top end for my built 3400/3500 hybrid. year is an 05' from a G6 with under 15k on it. im asking $350
-
[SIGPIC]
12.268@117... 11's to come!
turbo 3400: 358whp and 365tq at 9 psi
ASE Master Technician. GM Certified.
http://www.youtube.com/watch?v=7ibU1k8UZoo
http://www.youtube.com/watch?v=GUqJyopd720 -
by chance does it have an oil pan with it -
yea it does. sorry about that, its a full bottom end, minus heads, intake manifolds etc.[SIGPIC]
12.268@117... 11's to come!
turbo 3400: 358whp and 365tq at 9 psi
ASE Master Technician. GM Certified.
http://www.youtube.com/watch?v=7ibU1k8UZoo
http://www.youtube.com/watch?v=GUqJyopd720Comment
-
Where are you located?
Just so happens I have an entire 3500 top end w/gaskets anyways. Shipping would probably kill me tho.
Comment
-
Put a bid on uship.com and you'll probably save a bunch in shipping. I shipped a 3500 short block from AR to IL and it was maybe $150, whereas it was over $400 using a standard carrier.-Brad-
89 Mustang : Future 60V6 Power
sigpic
Follow the build -> http://www.3x00swap.com/index.php?page=mustang-blogComment
-
7484 crank?1996 beretta w/a 04' 3400 3.5 top end, 42.5lb hr, 180*thermo, t3t4 .63ar 60 trim, LC1 WB, FMIC, greddy rs BOV,TIAL 38mm wastegate,791xv,fidanza,stage III clutch,TG LSD,ffp udp,walbro 255 lph,strut tower brace,22 rear sway,30 front sway,92 5sp tranny,92 subframes,all solid mounts,kyb shocks and struts,eibachs,battery in trunk,tgp map sensor,DHP Powrtuner,euro front and rear and more to come soon...mods sitting in boxes waiting install....zo4 kit,GTU wing,and more..Comment
-
no, not the 7484 crank unfortunately[SIGPIC]
12.268@117... 11's to come!
turbo 3400: 358whp and 365tq at 9 psi
ASE Master Technician. GM Certified.
http://www.youtube.com/watch?v=7ibU1k8UZoo
http://www.youtube.com/watch?v=GUqJyopd720Comment
-
can you sell me the oil squiter and bolt from that engine ?Comment
-
i want to keep it complete plus i dont want to take it apart...[SIGPIC]
12.268@117... 11's to come!
turbo 3400: 358whp and 365tq at 9 psi
ASE Master Technician. GM Certified.
http://www.youtube.com/watch?v=7ibU1k8UZoo
http://www.youtube.com/watch?v=GUqJyopd720Comment
-
lol its still sitting at my house.Originally posted by MidnightriderZ24 View Post
I think i took some small shit off of it for placement of the jackshaft and shit.Comment
-
bump[SIGPIC]
12.268@117... 11's to come!
turbo 3400: 358whp and 365tq at 9 psi
ASE Master Technician. GM Certified.
http://www.youtube.com/watch?v=7ibU1k8UZoo
http://www.youtube.com/watch?v=GUqJyopd720Comment
-
do you have any pics of the engine i may be interestedComment
-
here you go.Originally posted by rx191 View Post
not much but you get the point. its the bottom end of the motor. woopdy.Attached FilesComment
-
-
if it had the steel crank id be all over it.. but i cant have anymore engine failures with the amount of power im putting out lol.. good luck with the sale.. if you have a short block with the steel crank let me know.. ill pick that up from you1996 beretta w/a 04' 3400 3.5 top end, 42.5lb hr, 180*thermo, t3t4 .63ar 60 trim, LC1 WB, FMIC, greddy rs BOV,TIAL 38mm wastegate,791xv,fidanza,stage III clutch,TG LSD,ffp udp,walbro 255 lph,strut tower brace,22 rear sway,30 front sway,92 5sp tranny,92 subframes,all solid mounts,kyb shocks and struts,eibachs,battery in trunk,tgp map sensor,DHP Powrtuner,euro front and rear and more to come soon...mods sitting in boxes waiting install....zo4 kit,GTU wing,and more..Comment
-
Wanna hook a V6 brother up with the ICM/Coilpack setup, bracket, plug wires and CPS to ICM wire harness?
I know it's useless as of right now but after i get mine running on the external 7x setup i'd like to play around with the 58x stuff...
Thanks,
DaveComment
Comment