Massive Performance Parts SALE!!!

[Mach 5]

Im consolidating every ad in to one massive thread.. I will be constantly adding things on here all mostly for 1st gen w-bodys.







GT3076R 5 bolt t2 w/ internal wastegate actuator 10psi used 16k miles- $950neg



OEM Front upper Camber plates. slightly bent and could use some fab work- $140



Front Coil over set



Rear Coil Over Set



(I work for Falcon Clutches at night doing installs. very reputable shop in my area everything is hand made)

Falcon Clutches.. custom clutch. was on my Mach 5. comes with flywheel. has handled over 442lbtq to the tire so an est 530+tq crank. can also be serviced and re padded through me. 5k miles -$440 neg



Spec Stage 3 getrag 282- Falcon Clutches re pad- 3k miles- holds to around 330tq $180 can have cleaned and re padded for a fee.



-getrag 282 #1 -unknown condition. make offer



-getrag 282 #2 out of my Mach 5 has stainless Rodney Dickman input shaft seal sleeve- newish diff bearings- make offer-



-FFP- front dog bones- $150 neg



-FFP- underdrive pulley- SOLD



-I have manifolds and cyl heads



-Magnum Roller Rockers- 1.6:1



-WOTTECH roller turbo street strip cam- 16k miles- $200



-MRZ 62mm throttle body- SOLD



-TGP PLENUMS



-3.1l valve covers some painted some aren't



-3xxx oil pan $45 shipped good for those who want to modify for turbo oil drain and want to keep a factory pan



-NIB GM McLaren TGP Front Bumper- $800 PICKUP ONLY



-tgp log manifolds- $90 a set

some sets are ported some aren't

2 sets stock

1 set ported- made 321hp 408tq on these





-Forge boost Controller- natural aluminum color- $75 shipped



-LS Yellow Beehive Springs set -$50 shipped



-NEW GM OEM LH0 3.1 Rear Manifold- $55 shipped



-TGP Rad- Needs to be brazed and cleaned up- $200 Shipping is additional $60



-axles axles axlessssssss- many are new many aren't new will list eventually.. all for manual trans



-ST Lowering Springs- $100 shipped



-used 1.6 ratio roller rockers- 3xxx- 10mm stud set of 12 pushrods extra lmk measurement I have a set- $50 shipped



-Getrag 282 shift cables- still on car-



-Getrag 282 master/slave steel braided lines



-Brand Spankin New Dorman Fuel Tank- $90 pick up only



-New front fender in black primer.. cant remember which side Ill have to check later- $30 pick up only



-TGP Louvers- $100neg



--TGP Rebuilt Crossover- $400neg shipped



-



-





lots more I need to start going through stuff.. Mach 5 parts are still on Mach 5 but will be coming off within the next week or so.



trans and certain freight weight parts are pick up only





message me here or to Spoon93@gmail.com



Thanks

-Jarek

[ghrarhg]

Interested in the Cam. This is a 3x00 cam correct? Just checking since the majority of the other parts are gen 2 stuff.

[Mach 5]

sale pending on cam

[project 92z]

I'm interested in the front and rear coil over sets. Your post mentioned mostly first gen. Are these, will they fit 91/93 Chevy Z34? Also, how old are they, and how much you askin' for them?

[Mach 5]

300 an axle so 600.. you would still need the upper mount cup for the rear to be fabbed up an I have O.E.M Front camber plates for $140 or $120 if the coil over set for the front is bought. price is with shipping 48 states..

the only issue is the design flaw regarding the front camber plates as they are slightly bent dude to what I believe is the lack of the support from the rather small adjuster plate. I would fab up a new design with a larger plate. I started n it but didn't finish it as plans have changed. These mount are no longer sold as far as I know... oh and the other thing is witht he coilover sleeves they may or may not fit the struts depending on the size on the inside but they can be modified to fit on a lathe.

yes it will fit a 91-93 z34. there is a whole writeup on w-body with exactly everything that needs to be done. BXX was one guy that did a writeup. another person I believe was Jay..

everything is new minus the camber plates. boxes haven't aged well in storage though but the parts are ok. Please let me know. Thank You

-Jarek

[Mach 5]

BUMP!!

[fisdad]

I really need a 5 speed shifter, clutch reservoir with lines and cables for a getrag HM-282 transmission 93-94 cavalier compatible.

[Mach 5]

I need that as well lol for my 89. Im sorry bud good luck in finding those parts

Bump for mee

[Forgotten User]

cam still available? If so pushrods with it?

[G.I.Ceo]

I took the cam a few weeks ago. I couldn't let another one pass me by.

[chevy454]

"-used 1.6 ratio roller rockers- 3xxx- 10mm stud set of 12 pushrods extra lmk measurement I have a set- $50 shipped"

Still available?

[koolcamaro]

Is the getrag stage 3 clutch still available? This is a pull style clutch correct?