Tweet
I sold my 01 GAGT a few weeks ago and picked up a econo car to drive until I get my 00 GAGT Built. Modding two GAGT's really wasn't practical and it now gives me time to focus on modding one car. So now I have tons of extra parts that I am not going to be using, thus the part out.
Note: Shipping will be determined by your zip code. I am not doing the dibs thing, therefore the first one with money in hand will get the part(s).
Pics of actual items can be found on my photobucket page:
1. New Comp Cams Camshaft, obtained through WOT-Tech and designed for optimal fuel economy as well as increased power over a stock cam. 20 ft/lbs of torque increase at low rpm and around a 8-10hp peak increase in power. $250.00
2. 2 New Rear Hub/Wheel Bearing Assemblies (Not Sure on Brand) $45 each or $80 for the pair
3. New 3400 Throttle Body (Metal Linkage check photobucket for pics) $25
Sensors not included.
4. Two sets of Valve Covers $8.00 per set
5. Two Sets of 10mm 3400 rocker arms $25 per set
6. Five sets of stock pushrods $5 per set
7. 99 Grand Am Air Bag Set with control module (Best Offer)
Install them in a wrecked car or blow them up next 4th of July
8. 4T65E HD Trans Conversion Side Mount Weld on Tab + Stock Side Mount $80
I purchased the 4t65e HD trans out of a the SCT concept car and had my machine shop make a weld on tab for my daily driver that was sold. I can have more made if there is interest and I have pictures of the 3 mounts used on the concept car that I can send with purchase.
9. Mount plate to mount a Vortech V9 supercharger to a 4T65E transmission $125 Note: Mounting plate was designed to fit a W-body. You will still need to fab the transfer shaft to connect the drive to the pulley system.
10. Mount plate to mount a Vortech V9 supercharger to a 4T45E transmission $125 Note: Mounting plate was designed to fit a N-Body (Grand AM) . You will still need to fab the transfer shaft to connect the drive to the pulley system.
11. Misc. RSM/Zspec supercharger drive shaft parts $150.00
Note: Most of these items have some damage and would be best used for mock up and redesign as the RSM/Zspec supercharger kits had drive shaft issues. They would also prove a excellent resource if you were to have a machine shop redesign/remake these parts.
Again, all pictures are on my photobucket account:
Please PM me with any questions and or interest.
Note: Shipping will be determined by your zip code. I am not doing the dibs thing, therefore the first one with money in hand will get the part(s).
Pics of actual items can be found on my photobucket page:
1. New Comp Cams Camshaft, obtained through WOT-Tech and designed for optimal fuel economy as well as increased power over a stock cam. 20 ft/lbs of torque increase at low rpm and around a 8-10hp peak increase in power. $250.00
2. 2 New Rear Hub/Wheel Bearing Assemblies (Not Sure on Brand) $45 each or $80 for the pair
3. New 3400 Throttle Body (Metal Linkage check photobucket for pics) $25
Sensors not included.
4. Two sets of Valve Covers $8.00 per set
5. Two Sets of 10mm 3400 rocker arms $25 per set
6. Five sets of stock pushrods $5 per set
7. 99 Grand Am Air Bag Set with control module (Best Offer)
Install them in a wrecked car or blow them up next 4th of July
8. 4T65E HD Trans Conversion Side Mount Weld on Tab + Stock Side Mount $80
I purchased the 4t65e HD trans out of a the SCT concept car and had my machine shop make a weld on tab for my daily driver that was sold. I can have more made if there is interest and I have pictures of the 3 mounts used on the concept car that I can send with purchase.
9. Mount plate to mount a Vortech V9 supercharger to a 4T65E transmission $125 Note: Mounting plate was designed to fit a W-body. You will still need to fab the transfer shaft to connect the drive to the pulley system.
10. Mount plate to mount a Vortech V9 supercharger to a 4T45E transmission $125 Note: Mounting plate was designed to fit a N-Body (Grand AM) . You will still need to fab the transfer shaft to connect the drive to the pulley system.
11. Misc. RSM/Zspec supercharger drive shaft parts $150.00
Note: Most of these items have some damage and would be best used for mock up and redesign as the RSM/Zspec supercharger kits had drive shaft issues. They would also prove a excellent resource if you were to have a machine shop redesign/remake these parts.
Again, all pictures are on my photobucket account:
Please PM me with any questions and or interest.
Comment