Anything DOHC goes
I saw something written on the internet about the 3.4dohc having 275 hp when it was first designed but was taken to 200hp by cutting the fuel...
It's looking to me as I will have to remove the trans with the engine as there is not enough room to separate them in the engine bay( flexplate hangs...
I have seen alot of these new motor mounts on some of the z34s in here and I am wondering where to get them from and how much do they cost?
Has anyone had to replace this? The pipe from the cap to the gas tank. I have one coming in the mail and mine is leaking now when I fill up my tank....
94 olds cutlass sup 3.4l 111000m ive noticed recently that the engine rpm is staying at 1100 rpm when stopping at a traffic light then it ...
Hi guys i'm new on here i have a 94 gtp. my question is does anybody know if I can get this engine out from the top with an engine crane? I've been...
Is it as simple as drilling the hole for the cam sensor in the obd1 cam carrier? Or is it more than that? I have the old obd2 cam carrier but I feel...
Hi everyone, I am doing some prep work on a 1996 3.4 DOHC engine from a Monte Carlo. The exhaust crossover pipe was detached from the engine...
Just wondering if anyone has had one go on them and are they simple to change/repair? I noticed the fan speed getting weak in it last season, and...
What is the easiest way to get to the crank sensor? My car right now is having intermittent spark and the only thing I can think of is the crank...
1993 Z34 Lumina. About a month ago, I began noticing a bit of a noise coming from (I think) the r front wheel, with a corresponding "vibration" in...
let me start off by saying i don't want to offend any one here by the what i have done to a perfectly good 96 monte carlo Z! that being said i have...
I am looking into buying a complete factory long block DOHC and running it in an S10. Motor mounts are not an issue, I can fab them, the engine comes...
Went and played with my bump and run car for the first time this year. While I was playing with it, I noticed that the cam sensor was unplugged. I...
okay i dont know anything about this but i would like to learn. what i want to know what all is involved in switching either way, which is harder,...
I have done a number of searches on this forum looking for a stock 91-93 dyno chart that I can use as a baseline to compute volumetric efficiency. ...
I currently have a 96 DOHC in my Fiero, I have had problems with a noisy lifter. My question is I can get a complete top end from a 97 DOHC, are the...
I can not seem to find it now, but is there a way or place I can get the ign coil pack tested. I have an engine that cranks over, I have spark on...
i just tore my z34 engine down to the block and was wondering if i could reuse my piston rings.i cleaned them up a little to check for cracks or any...
Ok, so as we have all been aware since somewhere in early 05-06, GM decided to revive the 60* DOHC. It really comes in 2 forms (duh). The 3.6 PFI...
Hi, my name is Clay. I live in Omaha and am friends with the forum member "Huskey".. Were working on rebuilding his GTP. Its pretty rough right now....
Before my 1992 DOHC - Fiero swap was done I came across a NOS '96 fuel rail with injectors on eBay. I bought it and used the injectors on the motor....
Hey Everyone, Does anyone know the flow rate (lbs/hr) of Stock 96'-97' 3.4 DOHC injectors? Thanks! Regards, David
here is what a piston & cylinder head looks like when a valve breaks off at the bottom of the valve stem. not a pretty sight. take a look at my...
Before I read in the forums that Boschs were bad, I bought a set, and had GM install them w/ new wires. I currently have Bosch +4's in car with...
Hey guys, just wondering if I were to swap a 3400 out of a Grand Am GT or something (got lots of those cars in our junk yard), would the 284 5-speed...
There are currently 3 users browsing this forum. (0 members & 3 guests)
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
